Low Price Guarantee
Wholesale & Govt
(Your shopping cart is empty)
AOR ARD9800 Fast Modem
The AOR AR9800 could be the biggest revolution in HF radio since SSB replaced AM
The ARD9800 is a modem unit that connects to the mic input of any transceiver. The user simply wires a connector for his particular transceiver, connects the speaker output of his transceiver to the modem and then connects the modem to a 12 VDC power source.
NORMAL ANALOG OPERATION OF THE TRANSCEIVER REMAINS INTACT
Digital voice HF is possible by selecting the Digital Mode
Incoming digital voice signals are automatically decoded, no selection necessary.
NO MODS TO THE TRANSCEIVER ARE NEEDED
1. The ARD9800 provides NEAR FM QUALITY audio using SSB.
2. The digital signals may require LESS SIGNAL than analog throughput making operations possible under adverse band conditions.
HOW DOES IT WORK?
Understand that this is a greatly simplified explanation: the ARD9800 digitizes the signal and divides into 36 PSK sub-signals in the bandwidth occupied by a normal voice audio signal.
IS IT LEGAL?
The ARD9800 uses an open published digital protocol (G4GUO) per FCC rules. In the USA, you may identify in digital or analog mode.
DOES IT WORK IN OTHER MODES?
Yes! The ARD9800 can be used in AM or FM modes, however, FM mobile operation could be prone to "picket fencing" which could result in the loss of data.
IS THERE A MARKET FOR THIS?
The ARD9800 was demonstrated for audiences at Dayton and Friedrichshafen.
HAMS LOVED IT! Most asked question was, "When is it available?"
WHAT ELSE DOES IT DO?
With the optional memory board, images can be easily transferred, similar to SSTV but we believe the ARD9800 sends a higher quality image. You can also send file transfers.
Owner can use ARD9800 mic, or a mic of their choice (wired for ARD9800 input).
WHAT MUST I DO TO GET ON THE AIR WITH THE ARD9800?
The ARD9800 package includes, modem, mic, cables and manual.
1. You must build (or buy) a cable that interfaces from the rear panel of the ARD9800 to the mic input of your transceiver, similar to a packet radio connection between a TNC (modem) and your radio. Then simply connect the mic input cable, the "speaker out" from your transceiver to the "audio in" on the ARD9800 and connect the power cable to the ARD9800.
2. It is suggested that you power the ARD9800 from a well regulated DC power supply. The use of "wall cube" and some "switching" power supplies is not recommended.
3. Be sure your mic and audio output settings are OK.
4. Make a test transmission in the analog mode prior to operating in digital mode.
ARE THERE OPERATING SUGGESTIONS?
1. Try to coordinate your frequencies as closely as possible. There is some small margin for error, but best results are obtained when both transceivers are exactly on the same frequency.
2. Be sure your audio filters are about 3KHz or wider.
3. Don't "overdrive" your ARD9800 with too much audio from your transceiver.
4. Don't transmit using "compression" (also known as a speech processor).
5. Be sure your ALC is within its specified operating region. If in doubt, lower audio output seems to work better than a higher setting.
6. Be mindful of your bandwidth when selecting a frequency on which to transmit. Be sure you will not interfere with operators on adjacent frequencies.
WHAT ABOUT DUTY CYCLE?
Your duty cycle will be more intense. This is important to users of amplifiers. Because the digital signal makes full use of the SSB audio bandwidth, you should consider that you will be transmitting at the maximum power output you have selected. At maximum power settings, this will likely result in your transmitter consuming more power and generating more heat. If you transmit images or large data files, your "key down" time could be three minutes or more.
ARE THERE OTHER SOURCES OF INFORMATION?
Below please find web sites that are NOT affiliated with AOR.
AOR takes no responsibility for their content.
300 Hz - 2500 Hz, 36 carriers
20 mS (50 baud)
36 carriers: DQPSK (3.6K)
+/- 125 Hz
Voice: Golay + Hamming
Video/Data: Covolution + Reed-Solomon
1 Sec. 3 tones + BPSK training pattern for synchronization
AMBE2020 coder, decoder
Automatic Digital detect, Automatic switching
between analog mode and digital mode
AOR original adaptive JPEG
10 ~ 16 V DC, Approximately 200 mA Typ(@ 12 V DC)
6 V DC by internal jumper setting
RS-232C, 9600 bps, Asynchronous
Dimensions (w, h, d):
100 x 32 x 158 (mm)
or 3.94 x 1.26 x 6.14 (inches) (Projections excluded.)
Radio: Microphone output (level adjustable)
Speaker input (500 mV ~ 5 V p-p), PTT (Push To Talk)
Video IN/OUT: NTSC 1 V p-p (75 ohm)
Microphone input, Speaker output, PTT input
Signal Encryption for commercial applications
(where permitted; special commercial version required)
Analog/Digital mode selector
Video capture/transmit switch
Specification & price subject to change without notice due to continuous development of the receiver. E & OE.
NOTE: Communications Receivers and accessories from AOR, ICOM and ALINCO are NOT accepted for return for credit, only exchange if defective within the first 30 days.
Share your knowledge of this product with other customers...
Be the first to write a review
HQ and Store - Holliston, MA
All order placed after 11AM
on Friday (03/07/2014)
will ship on Monday
30 Day Money Back*
Same Day Shipping*
New Products Only
Savings & Specials
Cape Cod Rebanding
Our Newest Products
BECOME AN AFFILIATE
SEND US FEEDBACK
Scanner Master Police Scanners Corporation
. All Rights Reserved.
Olark live chat software